[Rekognize]

If you didn't break any tabs because of this guide, hit the 'Thanks' button

 

[KrispyKreme]

Excellent.... will come in handy I'm sure....

Do you have a link to a PDF of this, would like to keep a hard copy...

Maybe this should be stickied as I'm sure it will be useful for a long time...

 

[SClown]

This is awesome thank you! sticky if not already.
Will use this tonight/tomorrow.

 

[SClown]

Ok so i still broke a tab for a under seat faring. Oops. Bit of super glue and i trust she'll be right.

 

[Truesday]

Ok so i still broke a tab for a under seat faring. Oops. Bit of super glue and i trust she'll be right.

I broke it too...

We'll see how strong the super glue bond is when i remove fairings for slider installation.

Sent from my R800x using Motorcycle.com Free App

 

[cruizin]

superglue is hopeless, jb weld to the rescue

http://www.jbweld.com/

used this to repair fuel tanks, radiators, fairing, radio control cars, and all sorts of other stuff

 

[Truesday]

superglue is hopeless, jb weld to the rescue

http://www.jbweld.com/

used this to repair fuel tanks, radiators, fairing, radio control cars, and all sorts of other stuff

I have some on hand but never actually used it. If it snaps again, I'll definitely JB weld it.

Sent from my R800x using Motorcycle.com Free App

 

[SClown]

The super glue was weaker than the strength of the gromett and didn't hold.

Installed my sliders last night. Refer other thread for details.

 

[silvertear]

I snapped the C grommets for the side covers :/ I'm going to see if JB weld will be able to fix it.

 

[bryce]

I snapped the C grommets for the side covers :/ I'm going to see if JB weld will be able to fix it.

I did the same thing. Egg shells man.


Sent from Motorcycle.com Free App

 

[Kurt]

You guys must be heavy handed, slow and steady never force pull.

Sent from Motorcycle.com App

 

[cruizin]

nice work Rekognise, added to our DIY Sticky of knowledge

 

[jeff]

You guys must be heavy handed, slow and steady never force pull.

Sent from Motorcycle.com App

Never force pull, only force push Luke.

Do it. Or do not. There is no try.

 

[Kurt]

Yes master yoda

Sent from Motorcycle.com App

 

[cruizin]

I did the same thing. Egg shells man. http://www.motorcycle.com/mobile

*sigh*
JB weld never lets me down.

i tell ya what, do you have any of this stuff available

http://www.selleys.com.au/putty/epoxy/knead-it-steel

this stuff is magic

& in worse case sceneraio, the mother of all plastic steel


DEVCON

http://www.devcon.com/products/products.cfm?familyid=101

just be careful though it doesnt work on all plastics but man it sets harder then a diamond this stuff, but dear as poison

 

[gottheneed]

I'm installing YOSH sliders right now and removing the fairings is a total bitch. I am not used to working with so much plastic! My '87 Volvo 240 is much more forgiving and needs less finesse

 

[Michael V]

I'm trying to remove the undertail so I can pull the air box out. I don't see any guides on how to do this, I unscrewed the fender and I unscrewed everything the undertail is connected to. Should I also disconnect all the cabling under the seat or will I be able to take the undertail off with those plugged in?

 

[Muilisx]

I tried finding this exact thing but for the 636, and unless I'm looking at the wrong thing, then it's no where as near detailed like the 300's.

 

[Cork]

looks like a lot of reading. anyone have a video?

 

[pogle301]

Lost Screws

Well.....I'm an idiot, a few months ago I changed out my headlights and lost some of the screws/bolts when putting the fairings back on. Anyone know where I can get replacements and how to tell which I need?